Vallox > MyVallox 125G CFi
MyVallox 125G CFi
MyVallox 125G CFi
MyVallox 125G CFi has all the properties of a modern ventilation unit, including constant flow fans. These fans allow the unit to compensate for differences in pressure and keep the air flows in balance in windy locations and tall buildings, during HR cell defrosting, and regardless of the heat recovery bypass status. The constant flow feature also compensates for separate extractions.
MyVallox 125G CFi has integrated humidity and carbon dioxide sensors that assess the indoor air quality and boost ventilation as necessary when the set humidity or carbon dioxide limits are exceeded. This makes the modern ventilation unit an easy and carefree solution for the user and it operates almost fully automatically. If, however, the user wants to control the unit manually, there are multiple control options. In addition to a traditional control panel, the unit can be controlled via a free cloud service or through building automation.
The new MyVallox 125G CFi also saves costs, since its heat recovery efficiency is significantly better compared to older models – nearly 80%. This means that the unit can recover and recirculate nearly 80% of the heat from extract air without the need to use the home’s primary heating system or the ventilation unit’s resistor.
The new constant flow function also makes the installer’s job easier because it allows litre-based air flow adjustment directly from the controller. The unit is overall faster to install, because MyVallox 125G CFi replaces Ilto 250, Ilto 270, Ilto 280 and Ilto 290 ventilation units directly without expensive duct modifications. For more details, check the unit’s replacement compatibility chart.
Replacing your ventilation unit increases living comfort and saves money.
MyVallox 125G CFi has integrated humidity and carbon dioxide sensors that assess the indoor air quality and boost ventilation as necessary when the set humidity or carbon dioxide limits are exceeded. This makes the modern ventilation unit an easy and carefree solution for the user and it operates almost fully automatically. If, however, the user wants to control the unit manually, there are multiple control options. In addition to a traditional control panel, the unit can be controlled via a free cloud service or through building automation.
The new MyVallox 125G CFi also saves costs, since its heat recovery efficiency is significantly better compared to older models – nearly 80%. This means that the unit can recover and recirculate nearly 80% of the heat from extract air without the need to use the home’s primary heating system or the ventilation unit’s resistor.
The new constant flow function also makes the installer’s job easier because it allows litre-based air flow adjustment directly from the controller. The unit is overall faster to install, because MyVallox 125G CFi replaces Ilto 250, Ilto 270, Ilto 280 and Ilto 290 ventilation units directly without expensive duct modifications. For more details, check the unit’s replacement compatibility chart.
Replacing your ventilation unit increases living comfort and saves money.
Including accessories: MyVallox Control controller, condensing water seal Vallox SilentKlick, wall mounting plate.
Description
Check the correspondence table to see if this model is suitable for replacing your old ventilation unit.
Read more and watch the videos of product introduction and installation of the ventilation unit.
Suitable for the following applications
Maximum recommended living area
180 m²
Annual efficiency (%)
75
Temperature efficiency of heat recovery (%)
80.9
SEC average climate
-38.937 kWh/m²a
Reference airflow rate
0.075 m³/s
Specific power input (SPI)
0.428 W/(m³/h)
Specific Fan Power (SFP)
1.541 kW/(m³/s)
Maximum extract airflow @ 100 Pa
111 l/s
Maximum supply airflow @ 100 Pa
107 l/s
Maximum supply airflow EcoDesign
384 m³/h
Duct outlets pcs
4
Duct outlet mm
125 mm
Product depth mm
601
Product width mm
598
Product height mm
525
Product weight
65.5 kg
Package weight
69 kg
ETIM EF003701 electrical connection
Connection cable with protective earthed plug
Mounting place
Wall
Remote monitoring options
MyVallox Cloud service, MyVallox Home network, External voltage message 0-10 VDC
Bus control
Modbus RTU (standard feature)
Extract air fan power consumption
0.165 kW
Supply air fan power consumption
0.165 kW
Sound power level
45 dB
Cell type
Cross-counter flow cell
Cell
Aluminium
HRU cell bypass
Automatic heat recovery bypass, partial bypass with cool recovery
Defrosting method
Vallox on-demand -defrosting automatics with heat recovery cell bypass
Post-heating
Electrical resistor, 900 W
Additional heating
Electrical resistor, 900 W
Electrical connection
230 V / 50 Hz / 9,8 A
Encapsulation class
IP34
Unit maximum power consumption
2.13 kW
MyVallox 125G CFi RA12
HVAC number: 7912243
The MyVallox Control control panel is included in the price.
Product weight: 65.5 kg
Package weight: 69 kg
GTIN: 6438326006453
MyVallox 125G CFi LA12
HVAC number: 7912244
The MyVallox Control control panel is included in the price.
Product weight: 65.5 kg
Package weight: 69 kg
GTIN: 6438326006460