Vallox > MyVallox 51 CFi enthalpy
MyVallox 51 CFi enthalpy
MyVallox 51 CFi enthalpy
The small size of the MyVallox 51 CFi ventilation unit and its HR cell material make it special. Because MyVallox 51 CFi is only 349 mm deep, it can be installed is a small space, e.g. above a toilet seat, without the need to enlarge the room. The enthalpy cell increases the humidity level of indoor air because both heat and humidity from the extract air, but not odours, travel through the plate heat exchanger’s films.
The unit makes the implementation of apartment-specific ventilation easy even in small apartments. In terms of air volume, the unit is suited to apartments with a maximum floor are of 75 m2.
A magnetic cover panel that hides the door screws can be installed on top of the MyVallox 51 CFi ventilation unit’s door to give it a more elegant look. The unit is stylish and barely noticeable even when visible. The unit can be controlled from a Vallox Delico PTD EC/KTD A or Vallox X-line PTXP MC/PTXPA MC/KTXA cooker hood or with a separate switch. Similar to other MyVallox units, MyVallox 51 CFi can be registered with the MyVallox Cloud service or connected to building automation for easy remote control.
To ensure minimal manual control, MyVallox 51 CFi’s integrated carbon dioxide and humidity sensors control the unit automatically. The sensors monitor the indoor air quality and boost ventilation automatically as necessary. Optional room-specific sensors, such as a humidity sensor, a carbon dioxide sensor, and a VOC sensor, can also be connected to the unit.
Thanks to its constant flow fans, the unit can compensate for differences in pressure and keep the air flows in balance in windy locations and tall buildings, during HR cell defrosting, and regardless of the heat recovery bypass status. The constant flow feature also compensates for separate extractions. The new constant flow function also makes the installer’s job easier because it allows litre-based air flow adjustment directly from the controller.
The unit makes the implementation of apartment-specific ventilation easy even in small apartments. In terms of air volume, the unit is suited to apartments with a maximum floor are of 75 m2.
A magnetic cover panel that hides the door screws can be installed on top of the MyVallox 51 CFi ventilation unit’s door to give it a more elegant look. The unit is stylish and barely noticeable even when visible. The unit can be controlled from a Vallox Delico PTD EC/KTD A or Vallox X-line PTXP MC/PTXPA MC/KTXA cooker hood or with a separate switch. Similar to other MyVallox units, MyVallox 51 CFi can be registered with the MyVallox Cloud service or connected to building automation for easy remote control.
To ensure minimal manual control, MyVallox 51 CFi’s integrated carbon dioxide and humidity sensors control the unit automatically. The sensors monitor the indoor air quality and boost ventilation automatically as necessary. Optional room-specific sensors, such as a humidity sensor, a carbon dioxide sensor, and a VOC sensor, can also be connected to the unit.
Thanks to its constant flow fans, the unit can compensate for differences in pressure and keep the air flows in balance in windy locations and tall buildings, during HR cell defrosting, and regardless of the heat recovery bypass status. The constant flow feature also compensates for separate extractions. The new constant flow function also makes the installer’s job easier because it allows litre-based air flow adjustment directly from the controller.
Including accessories: Condensing water seal Vallox SilentKlick, wall mounting plate.
- Maximum recommended living area 75 m²
- Maximum extract airflow @ 100 Pa 45 l/s
- Maximum supply airflow @ 100 Pa 44 l/s
- Maximum supply airflow EcoDesign 157 m³/h
Suitable for the following applications
Maximum recommended living area
75 m²
Temperature efficiency of heat recovery (%)
88.1
SEC average climate
-42.372 kWh/m²a
Reference airflow rate
0.031 m³/s
Specific power input (SPI)
0.281 W/(m³/h)
Specific Fan Power (SFP)
1.012 kW/(m³/s)
Maximum extract airflow @ 100 Pa
45 l/s
Maximum supply airflow @ 100 Pa
44 l/s
Maximum supply airflow EcoDesign
157 m³/h
Duct outlets pcs
4
Duct outlet mm
125 mm
Product depth mm
349
Product width mm
598
Product height mm
668
Product weight
50 kg
Package weight
54 kg
ETIM EF003701 electrical connection
Connection cable with protective earthed plug
Mounting place
Wall
Remote monitoring options
MyVallox Cloud service, MyVallox Home network, External voltage message 0-10 VDC
Bus control
Modbus RTU (standard feature)
Extract air fan power consumption
0.035 kW
Supply air fan power consumption
0.035 kW
Sound power level
37 dB
Cell type
Cross-counter flow cell
Cell
Enthalpy
HRU cell bypass
Automatic heat recovery bypass, partial bypass with cool recovery
Defrosting method
Vallox on-demand -defrosting automatics with heat recovery cell bypass
Post-heating
Electrical resistor, 900 W
Electrical connection
230 V / 50 Hz / 4,24 A
Encapsulation class
IP34
Unit maximum power consumption
1 kW
MyVallox 51 CFi RE01
SKU: 4128158
Product weight: 50 kg
Package weight: 54 kg
Control panel needs to be ordered separately.
GTIN: 6438326006194
MyVallox 51 CFi LE01
SKU: 4128159
Product weight: 50 kg
Package weight: 54 kg
Control panel needs to be ordered separately.
GTIN: 6438326006200